UPDATE: WORKS!!!! Is there an AUTO - Data Disconnect regedit?
 

1. Navigate to HKLM\Comm\CommMgr\Planner\Settings\

2. Delete the following key: "SuspendResume"

3. If this key doesn't exist add "CacheTime" value of 60

3. Soft Reset the device

I can now answer calls while DATA is ON. It will Disconnect when idle for 60 seconds.

Thanks wizkidd04

Re: Is there an AUTO - Data Disconnect regedit?
 

HKLM\Comm\CommMgr\Planner\Settings\SuspendResume = CDMA_bye_if_device_off
HKLM\Comm\CommMgr\Planner\Settings\CacheTime = 60 (1 minutes)

Works for CDMA. Note that if Exchange push is enabled, the data is always connected. Also some java midlets hold a data connection.

Re: Is there an AUTO - Data Disconnect regedit?
 

Thank you, a few users have been having this problem of their Data being continuously connected after installing the S2A CAB from my post. I tried it on my phone and the data does disconnect, even with exchange push email set up. One thing I noticed is that the data actually disconnects, not just suspends or goes dormant. Another thing, I used to normally get emails on my phone about 15 seconds before they would show up in my outlook on pc. So far, all the emails I received after this edit showed up on my pc about 1 min before it shows up on my phone. I am not sure if this is because the reg edit though, because sometimes this would happen before randomly. I will report back if I do end up getting them on my phone first like before. Thanks again.

Another issue I run into with this reg edit is the delayed answer or non answer phone call when data is connected.

Here's my thread on the S2A, check it out if you want.

http://forum.ppcgeeks.com/showthread.php?t=51295

Re: Is there an AUTO - Data Disconnect regedit?
 

AGH! The above registry edit does turn off the data connection, but is has the issue of not being able to answer a call if a data connection is open. Darn, so close. Thanks again.

Re: Is there an AUTO - Data Disconnect regedit?
 

SO..

HKLM\Comm\CommMgr\Planner\Settings\SuspendResume = CDMA_bye_if_device_off

Still has issues with unable to answering calls while DATA is connected?

Re: Is there an AUTO - Data Disconnect regedit?
 

I cannot see why this registry mod will block incoming calls, it'll only allow calls coming. Here is a little more details about data connection and call block:

If data is EVDO or 1X, calls won't be blocked, even if data is connected.
If it is connected over 1X (not EVDO), calls are blocked if there is a data activity going on.
If it is connected over QNC, calls are always blocked, regardless data activity.

If data is disconnected, there is no reason for call block. Something else is wrong on you your phone.

If you have set up an exchange account and set it to pick up as items arrive, the data connection will be always resumed. So will if you have other push running such as ImapPusherService.

Re: Is there an AUTO - Data Disconnect regedit?
 

The phone lights up ...but you just cant answer it. for some reason... i haven't tried that regedit yet.

Re: Is there an AUTO - Data Disconnect regedit?
 

When Data Connection is Dead for me icon is satellite dish with bars. Stock would be Tower with bars, calls come through fine and are able to answer without a problem.

When Data Connection is current my icons there are two pink arrows with the bars. Stock icons would be white arrows. Calls come in they are not blocked, they ring, lights flashes, anwser/ignore skin displays, but when pressing answer button on screen or hardware button nothing happens and phone continues to ring.

When Data Connection is suspended/dormant/sleeping my icons are two blue arrows with the bars. Stock would be two greyed out arrows. Have not gotten the phone to this point with the above reg edit. Even with push email turned off. Phone either has data connection current or off.

I don't know why it is doing, I just know that it is. Hope it helps.

I think this was the same issue being discussed here.
http://forum.ppcgeeks.com/showthread...e+answer+calls

Re: Is there an AUTO - Data Disconnect regedit?
 

Then try this instead:

HKLM\Comm\CommMgr\Planner\Settings\SuspendResume = GPRS_bye_if_device_off

Re: Is there an AUTO - Data Disconnect regedit?
 

Thanks. That is the same edit that DaimondTweak or AdvancedConfig enables, that people were having the issue with originally. That is why the original edit you posted with CDMA, I thought that would have fixed that issue.

Also, I think the unable to answer calls with data connected my be with the HTC phone skin. I will try to enable the WinMo phone skin and see if the results are the same.

But I will give it a try. I am hard resetting my phone right now to get it fresh!

Re: Is there an AUTO - Data Disconnect regedit?
 

After Hard Reset.

Tried first edit, data turned off. But if call comes in when data is active, unable to answer.

Tried second edit, same results.

Tried first and second edit with HTC phoneskin disabled, same results.

Oh and by the way using stock Sprint ROM.

Try to open Opera and call yourself, when I do that like I stated earlier call comes in, rings, lights up, but when pressed answer button on screen or hardware phone does not respond. Just continues to ring. If that does not happen to you Fix, maybe it is because the diff ROM I guess.

Re: Is there an AUTO - Data Disconnect regedit?
 

From what I can tell, the SuspenResume value needs to be set to #777 on CDMA devices, otherwise it doesn't know how to suspend an active data connection in order to take the incoming call (this would only affect phones that are currently using data, and not just idle).

has anyone tried just using the other reg tweak, and leaving SuspendResume at #777?

It would be nice if I could just trust my phone to turn off the data connection, instead of manually doing it every time.

Re: Is there an AUTO - Data Disconnect regedit?
 

After trying all the fixes in this thread I still could not recieve calls when the data connection was active.

BUT I think I may have finally solved this issue after playing around with issue for hours. I am running an (Touch Pro on Verizon with stock rom).

1. Navigate to HKLM\Comm\CommMgr\Planner\Settings\

2. Delete both of the following keys: "SuspendResume", and "CacheTime"

3. Soft Reset the device

4. Navigate back to the same registry path and ONLY recreate the DWORD value for "CacheTime". And set it to 60 (1 minute connection timeout)

5. Soft Reset the device again

6. Now the auto timeout data connection should work and you should still be able to recieve calls when the connection is active ( at least this works for me). :mrgreen:

Re: Is there an AUTO - Data Disconnect regedit?
 

WOW it works! It auto disconnects and I can ANSWER PHONE CALLS WHILE DATA IS ON.

But to keep it simple. Just DELETE "SuspendResume" key and keep the "CacheTime" to 60 seconds. RESTART.

Re: UPDATE: WORKS!!!! Is there an AUTO - Data Disconnect regedit?
 

Thanks for the info. I'll test this out before I do my next ROM dump.

One thing to note though:
nuPower tells me that EVDO off mode and suspend mode seem to use about the same amount of power. About 66 mA for me.

Re: UPDATE: WORKS!!!! Is there an AUTO - Data Disconnect regedit?
 

Pure Awesomeness! Thanks wizkidd04

Re: UPDATE: WORKS!!!! Is there an AUTO - Data Disconnect regedit?
 

data disconnect seem to work, however, during data session, you will not be able to pick up incoming call.

you may need to hard reset so becareful with this reg hack.

Re: UPDATE: WORKS!!!! Is there an AUTO - Data Disconnect regedit?
 

With both "SuspendResume" and "CacheTime" my connection disconnects AND I can pick up calls during data sessions instantly. Without "SuspendResume", calls come through but take over 5 seconds to actually pick up the call after I answer. It sort of freezes at the answer screen while this happens.

Re: UPDATE: WORKS!!!! Is there an AUTO - Data Disconnect regedit?
 

Well I deleted "SuspendResume" and now I can't get a data connection, and I can't put the "SuspendResume" back. PHM Regedit would just freeze and I have tried a few other regedit tools which allow me to put the key back but I still can't get a data connection. Any thoughts???

Re: UPDATE: WORKS!!!! Is there an AUTO - Data Disconnect regedit?
 

I would like to add to the question and ask, what was the original Dword Value of the Key? Everything functions fine, except that now, there's a pause WHENEVER I go to use the net, even if the connection is already there, so basically, I restored the key, but now do not remember the DWord value. Any help is appreciated.

Re: UPDATE: WORKS!!!! Is there an AUTO - Data Disconnect regedit?
 

key: SuspendResume
type: REG_MULTI_SZ
value: #777

Re: UPDATE: WORKS!!!! Is there an AUTO - Data Disconnect regedit?
 

Thanks! I'll also add that when I restored the key (without it being multistring or with #777), get this, it worked fine. Go Fig. But I've just changed things now. Thanks!

I also just changed the Cache Time to 300. (5 min)

Re: UPDATE: WORKS!!!! Is there an AUTO - Data Disconnect regedit?
 

Well I was using GB-SOFT Tweak on my 800W (Sprint) and it changed the value fro #777 to the other setting that everyone is talking about. HOWEVER, now I cant answer a call right away, it takes EXTRA time when the phone rings and I press the answer key. I am still wanting to have it automatically disconnect the data service if not in use after so many minutes to save battery life but I DONT want the delayed answer issue.

I aam now trying something. I set the TWEAK program to 10 minutes and let it adjust the registry.. then I changed the setting back to #777 amd waited and did a soft-reset. I left the other registry setting that will allow for the # of seconds on timeout set to 10 minutes and we will see if it still disconnects. I would like for this to happen to save battery life. Will this work and if not, what can I do to have it disconnect the data when not in use but still answer the phone without a delay.

ANy suggestions??

Re: UPDATE: WORKS!!!! Is there an AUTO - Data Disconnect regedit?
 

Does not look like my idea worked.. NOw it does not disconnect.. How do I know if my data connection is IDLE? I want it to disconnect after a certain amount of time so it will save batter life BUT not have the phone answer issue...

Re: UPDATE: WORKS!!!! Is there an AUTO - Data Disconnect regedit?
 

Okay, here's a way to at least easily disconnect your data when you need to without going to the CommManager. This was taken from the Titan forum and it is a reg edite that I used to use on my old Mogul. Props "itsall cooool" to for posting it.

This edit allows you to see the duration of your Vision connection along with a button to disconnect it.
You see it in the bubble that is displayed when you tap the Vision icon on the top taskbar (the evdo (or 1x)box).


Click HKEY_LOCAL_MACHINE
Click ControlPanel
Click Phone
Click the bottom menu 'edit'
Select new dword value
Change the value name to "Flags2" (no quotes).
Select the 'hexidecimal' button.
Type 10
Click ok.
You should now see in the 'name/data' section:
Flags2 16 (0x00010)
exit regedit

When done, wait a full minute, then soft-reset the device.

This was done this PHMregedit, but this works for RescoExplorer too (what I used)

~Journey

Re: UPDATE: WORKS!!!! Is there an AUTO - Data Disconnect regedit?
 

how can i restore suspendresume file?

Re: UPDATE: WORKS!!!! Is there an AUTO - Data Disconnect regedit?
 

Since there are no real solutions to automatically disable data connections, while you edited SuspendResume there are options. For those who have e-mail linked to their phone might want to try this:

1. Start>Settings>Personal>Buttons( on the bottom of the screen are tabs, click END tab.) Now check off Automatically execute the selected action. Then check off Terminate data connection.

*Note* This option is great for when you notice data connection running. Just hold the END key to turn it off.

2. Having e-mail accounts on your device also start your connection. When setting up accounts you have options whether to Manually check mail or have the device check on a timed basis, the less checks it makes the better on battery life. I have mine set to EVERY 4 HOURS theres also ONCE A DAY.
Now After that click ADVANCED SETTINGS and UNCHECK Send/Receive when i click Send.
***That option solves alot of problems. people don't realize with that option active, every time you press the Send key Data connection starts up to check for e-mail.


I hope this helps. Would be nice if there was a program that would keep my #777 in Suspend/Resume and automatically disable data connection. Advanced Config & Diamond Tweak dont work, they just set it back to GPRS in Suspend/Resume. Making it impossible to answer phone calls without a delay.