Hard-SPL - Flashing ROMs - Titan Unlocker - Click Here!

[alraune]

OK i know this has probally been asked tons of time. But what size SD Cards let you flash roms? I have a 2gb NON-HC Micro SD Card and it doesnt do anything when i boot into the bootloader and have the card in with the .nbh file on it.

[GnatGoSplat]

2GB should work, it has to be formatted FAT32.

[Bad Sector]

I need help on relocking too, please! No matter what rom I have on my phone, If I soft reset it I get stuck in 2.40 Olipro bootloader and it is HELL to try to get it out. After trying exit bootloader and mtty over and over at some point it does finally kick me out of bootloader.


And by not working, I mean I connect to the 6800 and I am able to run the Exit bootloader or even connect thru USB to mtty and send the set 0 16 and task 8, the phone gets the command and then looks to reset, but then just pops back into bootloader.

I have also tried to put TITAIMG.nbh on a 512 meg storage card formatted properly from dos and power-cam reset to try to make it load a new rom to kick it out of bootloader, but it always says "No Image Found".


So I am sure when I send it in, they will see the 2.40 Olipro bootloader screen.

Can anyone tell me a safe way, if there is, to change to a newer htc bootloader or sprint bootloader so that I can return?

Thanks,

[Bad Sector]

Well, I just tried to reflash the Hard-SPL to 2.40 Olipro again, just to try to see if a fresh install would help it. I connected and ran the Hard-SPL-MFG, followed the steps and it took me to the bootloader. I unplugged and plugged back in, and it went on to the RUU. When I click ok and next for the RUU to go, I get Blue Screen of Death on computer for Multiple IRQ or something to that effect... so once again, I am back... stuck in bootloader.. oh the pain...

Someone please help!!!! lol.. dying over here...

[Bad Sector]

Another update... I was some how magically able to RUU_TITAN_SPRINT_WWE_3.35.651.2_RS_TITAN_3.35.04_4 350H_SPCS_AM_Ship to initiate the phone to flashing the rom from boot loader...

So it went thru and flashed the rom... then it reset and went BACK TO BOOTLOADER!!! arrgg... i think i'm going to go insane here...

[Bad Sector]

Update!!!!

Ok, did some reading on the MTTY commands. I know everyone told me to do the "set 16 0", but I also saw that the "set 14 0" will set it to start in OS mode. So I did "set 14 0" and it returned some HTC*#(&$( garbage.. then I did "set 16 0" and it didn't return anything (normal) so then I did "task 8" and it reset the phone.

But that came back immediatly into bootloader. So I took out the battery, left it out for 1 min, put it back in, and plugged it back into the USB. This time the bootloader screen did not come right back up (GOOD!!!), after about 20 secs, the power light turned yellow.. then to green.. it is waiting for me to hit power button to turn on right now... WHEW!!!!!

I still need to solve this problem with 2.40 Olipro though... I can't keep fighting this every time I need to soft-reset the device...

So if anyone has any more help or suggestions on the best way to change to an offical bootloader, let me know! Thanks

[Bad Sector]

Tested it just again to make sure that worked, and it does! Everytime I hit reset, I get shot to bootloader..

To get out of Bootloader I do the following:
set 14 0
set 16 0
task 8

unplug phone, remove battery, replace after 30 sec, plug in usb cable and wait for yellow light. Press and hold power for 1 sec or so till it boots.

Atleast I have an escape method now

[jmann91]

After using Oilpro to unlock my Sprint Mogul I was able to successfully use BuildOS to upload the No2Chem ROM to my device. Everything seemed to work properly the phone did its normal boot and start-up after an update and the bootloader screen is gone.

Problem is once I unplug the phone from USB the device will run fine for about 30 to 45 seconds then reboot. It boot back into normal mode but 45 seconds later it will reboot again. Plugging it back into the USB stops the re-booting.

What do I need to do to fix this problem?

John

[Bad Sector]

^ Is that the problem where you need to remove the battery for a little while and then replace it? Give it a shot....

[jmann91]

Not sure if its the problem or if I have the wrong OS build.