'Slide to Answer/Ignore' doesn't work

[3DPiper]

Suddenly my 'Slide to Answer/Ignore' doesn't work.. I can slide it all the way the left (answer/green) and it just sticks to the end and doesn't answer the call.. To make matters worse, when I'm trying to answer a call I can't even just hit the phone button.. It also doesn't answer the call.. I usually have to wait for the person to stop calling me and then call them right back.. Ignore/Right still works..

What could cause this?

I need to answer calls!

-Matthew

[zone23]

Advanced Config can cause this have you used it? Usually its when you turn the data setting to standby at 1 min. or whatever. What you describe is the exact effect of standby. I haven't had any problems answering my phone once I stopped messing with the standby thing. It doesn't really save any battery anyway.

Also some other program may have changed the following key:

"HKLM>Comm>ConnMgr>Planner>Settings" were:

"SuspendResume"="#777"

it probably says something like "GPRS_bye_if_device_off"

This is all posted in the threads if you search for it you will get even more information, I know how hard this stuff can be to find. Especially when someone probably has the answer off the top of there head.

[3DPiper]

I do have Advanced Config, but I don't recall setting it to data stanby.. Where is that setting located? I'll check it..

Thanks!

-Matthew

[zone23]

Originally Posted by 3DPiper

I do have Advanced Config, but I don't recall setting it to data stanby.. Where is that setting located? I'll check it..

Thanks!

-Matthew

The best thing to do is pop open your registry editer and go to this key:

"HKLM>Comm>ConnMgr>Planner>Settings" were:

"SuspendResume"="#777"

A lot of chiefs cook in registry editors like PHM Regedit.

Something else may have changed the setting.

incase you don't know:

Launch PHM Regedit

click +HKEY_LOCAL_MACHINE
click COMM
click COMMMgr
click Planner
click Settings

you should see SuspendResume #777

if you see anything else you need to change it to #777 just click on it Value data: #777

[3DPiper]

My SuspendResume contents show:

7E 00 47 00 50 00 52 00
53 00 21 00 00 00 00 00


Edit: didn't see your edit, i'll change it to 777 and see if that fixes it..


-Matthew

[zone23]

Originally Posted by 3DPiper

My SuspendResume contents show:

7E 00 47 00 50 00 52 00
53 00 21 00 00 00 00 00


Edit: didn't see your edit, i'll change it to 777 and see if that fixes it..


-Matthew

Just click dont hold, also whats it say in the window on the right "Data"?

[3DPiper]

This is what I see..

-Matthew

[zone23]

Mine reads:

23 00 37 00 37 00 37 00
00 00

I actually hate that PHM RegEditir the one NRGZ used always seemed better.

[erkme73]

Not to hijack - but along these same lines - how do you turn off Slide to answer/lock and the cheek-guard thing. I think it may be causing my dialer to crash out if I click 'end call' before the call connects.

[psycho_maniac]

do this one:
disconnect network when idle for 1 min
HKLM\Comm\CommMgr\Planner\Settings\
set "SuspendResume" to 58 00 00 00 33 00 99 00 88 00 39 00 58 00 39 00 29
add "CacheTime" value of 60
works awesome, i use it, and it disconnectes you from the network when your not using it.

oh and it solved the problem i had where i couldnt answer phone calls when i was connected to the network. it works good. when your connected to the network and you get a phone call. you will hit "answer" but it will take a few seconds for it to disconnect to the network and pick up the phone call.